倾斜中厚煤层错层位外错式巷道布置及相邻巷道联合支护技术

Layout and combined support technology of alternate exterior stagger arrang- ement roadway and adjacent roadways in inclined and medium-thick coal seam

  • 摘要: 基于倾斜中厚煤层沿空掘巷与支护技术展开研究。首先通过构建力学模型,依据基本顶最大弯矩确定基本顶的断裂位置及断裂形式,计算得在距离煤柱帮17.57 m处基本顶达到弯矩最大值23.02 MN·m,并进一步确定断裂线位于实体煤上方;结合“内外应力场”理论,确定在当前覆岩力学环境下“内应力场”范围为15.89 m;综合考虑煤柱的空间关系,分析巷道围岩煤柱尺寸,确定窄煤柱水平错距为7.37 m,竖直错距为2.40 m;综合以上分析确定区段煤柱留设尺寸范围为7~12 m,通过FLAC3D数值模拟软件对不同煤柱尺寸的应力场、塑性区分布进行计算分析,对掘进和回采两个阶段下不同煤柱尺寸条件下稳定性进行研究和验证,最终确定窄煤柱的合理宽度为8 m。然后根据倾斜中厚煤层错层位外错式巷道布置形式所具有的立体化空间形式,提出错层位外错式区段间相邻巷道联合支护技术并对其技术特点进行理论分析;基于围岩松动圈支护理论,通过计算确定区段间相邻巷道联合支护参数并利用FLAC3D数值模拟软件对区段间相邻巷道联合支护方案和矿方原支护方案进行模拟,分别从支护应力场、塑性区分布和围岩相对变形率三方面对掘巷和回采阶段下两支护方案的效果进行验证,最终结果表明区段间相邻巷道联合支护方案相对于矿方原始支护方案,更有利于巷道围岩的变形控制。

     

    Abstract: Research is conducted on the gob-side gateroad driving and support technology in an inclined and medium- thick coal seam. By constructing a mechanical model,the fracture position and fracture form of the main roof are deter- mined according to the maximum bending moment of the main roof. It is calculated that the main top reaches the maximum bending moment at a distance of 17. 57 m from the coal pillar and the maximum bending moment is 23. 02 MN·m,which further determines that the fracture position is located on the side of the solid coal. Combined with the “inside and outside stress field” theory,the calculated “internal stress field” range is 15. 89 m. Considering the space relationship of the roadway,the horizontal offset of the narrow coal pillar is determined to be 7. 37 m and the vertical offset is 2. 40 m. The above experimental analysis determines that the experimental range of the section coal pillars is 7-12 m. The stress field and plastic zone distribution of different coal pillar sizes are calculated and analyzed by the FLAC3D numerical simulation software and the dimensional stability of different coal pillars is studied and veri- fied under the two stages of excavation and mining. The reasonable width of the narrow coal pillar is finally determined to be 8 m. Based on the spatial structure characteristics of adjacent roadways in split-level roadway arrangement,the combined support technology is proposed and its technical characteristics are analyzed theoretically. The broken zone theory is used to determine the joint support parameters of the adjacent roadway and the FLAC3D numerical simulation software is used to simulate the combined support scheme and the original support plan. The effects of the two support schemes under different stages are verified from the aspects of support stress field,plastic zone distribution and relative deformation rate of surrounding rock. The final result shows that the combined support scheme is more conducive to the deformation control of the surrounding rock of the roadway.

     

/

返回文章
返回
Baidu
map